Skip to content

If something goes wrong

Find what you see in the left column. Messages are quoted as Fabricator writes them; Messages lists them all.

What you see What to do
New panels look scrambled Press Re-layout. This is normal for new panels.
A loop gives no panel The curve ends don’t meet. Press Check, then Heal Frame on the curves it marks. Look for an end that stops just short of a corner: Check marks an end that stops within 2 mm of one.
“Fabricator: solve not started — The map found no panels in this drawing. …” No closed outline is on an edge type. Put the curves on Fixed edge, Seam, Cable or Join, and close the outlines.
A panel is missing or has no number after a solve The frame has a flaw near it. Check, Heal Frame, solve again. Then try another Mesh detail.
The Atlas doesn’t show what is in Rhino Refresh reads the drawing again. Sync calculates everything again from scratch.
“Fabrication out of date — recalculate” at the foot of the map Press Sync.
A cut, join or detail is not made Rhino’s command line has a line with cut refused:, join refused: or feature refused: and the reason.
Nest does nothing Set a material: every piece needs one. If it still does nothing, look at Rhino’s command line for a support: line.
Output 2D patterns asks “Bake approximate panels?” The panels listed are flattened from the preview, not from a solve, and may be off by the amount shown. Click Cancel, run the 3D solver for those wireframes, and output again; or click OK — Output 2D patterns to output them as they are.
A window outline curve in Rhino comes back after you edit it Those curves are made by Fabricator. Copy one and edit the copy.
Undo won’t remove a seam A seam set on only one use of a curve can’t be undone that way. Set the seam again instead.
A stress spike at a corner between short edges Try another Mesh detail. Tell us which one showed it.
Curves come apart when you move one Wireframe connectivity is off. Click FrameConnect in the panel so that it is green, then snap the ends together again.
Shift+drag only moves the curves The extrude works on curves on the Fabricator edge layers, on a straight move, with FrameConnect on. Give the curves an edge type first.
“Select a wireframe in the viewport to solve” The drawing has several wireframes. Select the one to solve, then press Run 3D Solver.
“The Atlas could not be loaded; click FAB2D” Open the Atlas with the FAB2D chip, or the map button at the top of the panel.
What you see What to do
The Atlas’s panels have no cut lines, notches or labels, and the command line says “plan: The free plan shows the panel shapes. …” That is the free preview. A plan adds them: see Plans.
“Full solves, 2D patterns and nesting need an active plan (plan=free). …” Choose a plan on the website’s Billing page. On a team, the owner chooses it.
The same message with plan=pro or plan=day_pass Your plan has ended or its payment failed. Renew it or fix the payment on Billing. A Day Pass lasts 24 hours.
“Your team has no paid seat for you, …” Ask the team owner to buy you a seat or give you one. See Work as a team.
The account button says · Free though you paid Check Billing: the plan may still be turning on, or the payment may have failed. On a team, it is the owner’s plan that counts.
What you see What to do
“Can’t reach the Fabricator server” Check your internet connection, firewall or VPN, then click Try again.
“You’ve been logged out” Click Log in in the panel again. This happens after a computer is disconnected on the website’s Settings page, or after you leave or are removed from a team.
The browser says the code is no longer valid Codes last 10 minutes. Go back to Rhino and click Log in again.
“Update required to keep working” Click Update, then restart Rhino.
“The update didn’t install” Click Try again. If it fails again, Download manually opens the website’s download.
Rhino doesn’t know the commands, or still shows the old version Close Rhino completely and open it again after an install or an update.

Get help: Report a problem… in the panel’s account menu sends us your words with the plugin’s diagnostics and, if you tick it, the drawing.